HOME | ABOUT US | CERTIFICATIONS | CATALOG | CONTACT US | REQUEST QUOTE
 
 
  Translate This Page 
 
Featured
 
 
 
 

Extreme Angle Master Flash®

Specifically designed for the metal roof industry, for applications with a 35 to 65 degree angle, while accepting and responding to the most commonly encountered pipe penetrations.

The built in 40° pitch allow the Extreme Angle Master Flash to handle any extreme roof pitch, sleeve flexibility accommodates vibration and pipe movemet caused by expansion and contraction. Easy on site customization handles all normal installations, too.


MASTER FLASH® FEATURES

WEATHER PROTECTION

Made of EPDM or Silicone, these flashings are compounded specifically for maximum resistance to weathering due to ozone and ultraviolet light.

EASY ON-SITE CUSTOMIZATION

Fast, one piece construction allows for easy on-site installation in usually 5 minutes.

BASE FLEXIBILITY

The soft aluminum base is designed to form a seal on most panel configurations and roof pitches regardless of pipe location.

DESIGN EXCELLENCE

Aztec's flexible design meets virtually all roofing needs. Sleeve flexibility accommodates vibration and pipe movement caused by expansion/contraction. the soft aluminum base easily conforms to roof panels. Master Flash® was used to create a new engineering standard for profiled roofing by the International Association of Plumbing and mechanical Officials(for the uniform Plumbing Code) and remains the only product listed. These products are also listed for use with Type B vents. The addition of fire retarding agents milled directly into the rubber compound created a self extinguishing feature which enables it to be used with Type B vents. Listed with IAPMO certification No. 3121.

ADVANCED OZONE RESISTANCE tested to...

EPDM

70 hours @ 500 pphm

SILICONE

70 hours @ 500 pphm
HIGH TEMPERATURE RESISTANCE
Tested to Intermittent
  Continuous
 
+135ºC (+275ºF)
+100ºC (+212ºF)
 
+260ºC (+500ºF)
+225ºC (+437ºF)
LOW TEMPERATURE RESISTANCE tested to...
-55ºC (-67ºF)
-74ºC (-101ºF)
COMPRESSION SET minimum... 25% 50%

flashing calculatorTry our new Master Flash Roof Pitch Calculator which is designed specifically for Master Flash® products. Using this calculator in association with foreign or competitive products may result in installation failure. This Calculator is designed to provide assistance in planning only. It is to be used as a guide and not the ultimate source of information. Every effort has been made to make this as complete and accurate as possible. If you are installing on pitches greater than 10/12 or you desire further information, please call Aztec Washer: 1-800-WASHER-5.

Check diameter of your pipe or duct and select appropriate Standard Master Flash® to accommodate your application as indicated on the chart below. For extreme pitch or surface irregularity, select next larger size.

Sizing Chart
Check diameter of your pipe or duct and select appropriate Standard Master Flash® to accommodate your application as indicated on the chart below. For extreme pitch or surface irregularity, select next larger size.

PIPE SIZE US PART NUM FLASHING DETAILS
Extreme 1/4”– 5-3/4” Black EA101BA A-Top opening diameter Closed

6 - 146mm
B-Cut to suit pipe size 1/4”– 5-3/4” (6 - 146mm)


Silicone EA102RA C-Base dimensions 11” (279mm)

Flashing Detail

 
   
   
   
 
 
 
13821 Danielson St., Poway, California 92064 | 1-800-WASHER 5 (927-4375) | 1-858-513-4350 | Fax 1-858-513-4305

Master Flash®, Universal Master Flash®, Universal Retrofit Master Flash®, Retrofit Master Flash®, Residential Master Flash®,
Square Vent Retrofit Master Flash®, Master Seal® and Master Plug® are registered trademarks of Aztec Washer Company, Inc.
Please Note: Aztec Washer industry leading metal roof flashings and extreme angle pipe flashing products are available online from trusted retailers.

©2009-2013 Aztec Washer Company, Inc. | Site Map | Privacy Statement
 
  More Managed Sales and Marketing Services by Perpetual Prospects Unlimited, LLC