HOME | ABOUT US | CERTIFICATIONS | CATALOG | CONTACT US | REQUEST QUOTE
 
 
  Translate This Page 
 
Featured
 
 
 
 

Res Lead Master Flash®

This unique flashing was designed for residential use with a built in 20 degree pitch allowing adaptability to almost any roof pitch including 45 degrees. The clearly marked designation of pipe diameter takes the guess work out of sizing. A “C20 ASTM” additional requirement was added to ensure conformance to the most stringent ozone/weathering specifications available. This addition allows the rubber a minimum 20 year life.

Check diameter of your pipe or duct and select appropriate Res-Lead Master Flash® to accommodate your application as indicated on the chart below. For extreme pitch or surface irregularity, select next larger size.

RES-LEAD MASTER FLASH®

The addition of fire retarding agents milled directly into the rubber compoundcreated a self extinguishing feature which enabled conformity to "IAPMO"code requirements for Type B-Vents.A "C-12 ASTM additional requirement was added to assureconformance to the most stringent ozone/weatheringspecifications available.

EASY ON-SITE CUSTOMIZATION

The pull tab design and easy smooth tear grooving is intended to eliminaterazor cut and allow for circular hole."Environmentally safe" acrylic coated Safe-Lead Metal baseThe built in 20º pitch allows adaptability to almost any roof pitch including 45ºClearly marked designation of which step to tear out for whatsize pipe has taken the guess work out of sizing.

EPDM RUBBER IS AVAILABLE IN BLACK OR GREY

SILICONE IS AVAILABLE IN RED

CUSTOM COLORS AVAILABLE UPON REQUEST, ADDITIONAL COST MAY APPLY.

 
flashing calculatorTry our new Master Flash Roof Pitch Calculator which is designed specifically for Master Flash® products. Using this calculator in association with foreign or competitive products may result in installation failure. This Calculator is designed to provide assistance in planning only. It is to be used as a guide and not the ultimate source of information. Every effort has been made to make this as complete and accurate as possible. If you are installing on pitches greater than 10/12 or you desire further information, please call Aztec Washer: 1-800-WASHER-5.
 
Four sizes accommodate Flues & Vents From 1/4" Diameter Through 18" Diameter

PIPE SIZE US PART NUM FLASHING DETAILS
Mini 1/4”– 3” Black RL051BA A-Top opening diameter Closed

(6 - 76mm) Grey RL051GA B-Cut to suit pipe size 1/4”– 3” (6 - 76mm)


Silicone RL051RA C-Base dimensions 16" x 19 -1/4" (410 x 490mm)





#1 3”- 8” Black RL101BA A-Top opening diameter 2 -1/2" (63mm)

(6 - 203mm) Grey RL101GA B-Cut to suit pipe size 3”- 8” (6 - 203mm)


Silicone RL102RA C-Base dimensions 20" x 24" (508 x 609mm)





#2 8”- 11” Black LS201BA A-Top opening diameter 5 -5/8” (142mm)

(203 - 279mm) Grey RL201GA B-Cut to suit pipe size 8”- 11” (203 - 279mm)


Silicone RL202RA C-Base dimensions 26” x 30" (660 x 762mm)





#3 11” - 18” Black RL301BA A-Top opening diameter 8 -3/4” (222mm)

(279 - 457mm) Grey RL301GA B-Cut to suit pipe size 11” - 18” (279 - 457mm)


Silicone RL302RA C-Base dimensions 35” x 35" (889 x 889mm)

Flashing Detail


 

 

   
 
   
 
 
 
13821 Danielson St., Poway, California 92064 | 1-800-WASHER 5 (927-4375) | 1-858-513-4350 | Fax 1-858-513-4305

Master Flash®, Universal Master Flash®, Universal Retrofit Master Flash®, Retrofit Master Flash®, Residential Master Flash®,
Square Vent Retrofit Master Flash®, Master Seal® and Master Plug® are registered trademarks of Aztec Washer Company, Inc.
Please Note: Aztec Washer quality metal roof flashings and residential safe lead base pipe flashing products are available
online from trusted retailers.

©2009-2013 Aztec Washer Company, Inc. | Site Map | Privacy Statement
 
  More Managed Sales and Marketing Services by Perpetual Prospects Unlimited, LLC