ABOUT US | CERTIFICATIONS | CATALOG | CONTACT US | REQUEST QUOTE
 
 
  Translate This Page 
 
Featured
 
 
 
 

Universal Retrofit Master Flash®

The Universal Retrofit has been designed to accommodate existing applications where a standard pull over flashing cannot be installed. The split design allows an easy wrap around fit with a single stainless steel clamp for sealing.

Check diameter of your pipe or duct and select appropriate Universal Retrofit Master Flash® to accommodate your application as indicated on the chart below. For extreme pitch or surface irregularity, select next larger size. Simply split the flashing at the designated area and close with the stainless steel clamp as instructed on the installation instructions.

 

UNIVERSAL RETROFIT MASTER FLASH®

WEATHER PROTECTION

Made of EPDM or Silicone, these flashings are compounded specifically formaximum resistance to weathering due to ozone and ultraviolet light.

EASY ON-SITE CUSTOMIZATION

Fast, one piece construction allows for easy on-site installation in usually 5 min.

AVAILABLE IN BLACK OR GREY

FLEXIBLE BASE

Easily forms to contours of roof panel.


 
ADVANCED OZONE RESISTANCE tested to...

EPDM

70 hours @ 500 pphm

SILICONE

70 hours @ 500 pphm
HIGH TEMPERATURE RESISTANCE
Tested to Intermittent
  Continuous
 
+135ºC (+275ºF)
+100ºC (+212ºF)
 
+260ºC (+500ºF)
+225ºC (+437ºF)
LOW TEMPERATURE RESISTANCE tested to...
-55ºC (-67ºF)
-74ºC (-101ºF)
COMPRESSION SET minimum... 25% 50%
 
flashing calculatorTry our new Master Flash Roof Pitch Calculator which is designed specifically for Master Flash® products. Using this calculator in association with foreign or competitive products may result in installation failure. This Calculator is designed to provide assistance in planning only. It is to be used as a guide and not the ultimate source of information. Every effort has been made to make this as complete and accurate as possible. If you are installing on pitches greater than 10/12 or you desire further information, please call Aztec Washer: 1-800-WASHER-5.
 
Sizing Chart

PIPE SIZE US PART NUM FLASHING DETAILS
#1 3/4”- 2-3/4” Black RF 101 BS A-Top opening diameter 3/4” (19mm)

(19 - 70mm) Gray RF 101 GS B-Cut to suit pipe size 3/4”- 2-3/4” (19 - 70mm)


Silicone RF 102 RD C-Base dimensions 6 -3/10” (160mm)





#2 2”- 7-1/4” Black RF 201 BS A-Top opening diameter 2” (50mm)

(50 - 184mm) Gray RF 201 GS B-Cut to suit pipe size 2” - 7 -1/4” (50 - 184mm)


Silicone RF 202 RD C-Base dimensions 10 -3/4” (273mm)





#3 3-1/4” -10” Black RF 301 BS A-Top opening diameter 3 -1/4” (95mm)

(95 - 254mm) Gray RF 301 GS B-Cut to suit pipe size 3 -1/4” – 10” (95 - 254mm)


Silicone RF 302 RD C-Base dimensions 14 -1/2” (368mm)

Flashing Detail

 

 

   
   
   
 
 
 

13821 Danielson St., Poway, California 92064 | 1-800-WASHER 5 (927-4375) | 1-858-513-4350 | Fax 1-858-513-4305

Master Flash®, Universal Master Flash®, Universal Retrofit Master Flash®, Retrofit Master Flash®, Residential Master Flash®,
Square Vent Retrofit Master Flash®, Master Seal® and Master Plug® are registered trademarks of Aztec Washer Company, Inc.
Please Note: Aztec Washer flashings for metal roofs and universal round base pipe flashing products are available online
from trusted retailers.

©2009 Aztec Washer Company, Inc. Site Map | Privacy Statement

 

 
  More Managed Sales and Marketing Services by Perpetual Prospects Unlimited, LLC